Nearly every wood pallet in North America is one of two designs. Knowing which one you have, and which one you need, answers most of the practical questions people ask about pallets: how a forklift gets under it, how much it can hold, and why one costs more than the other.
Stringer pallets
A stringer pallet is built on three parallel boards, the stringers, usually 2x4s running the 48 inch length. Deck boards are nailed across the top and bottom. This is the standard GMA pallet and the overwhelming majority of what you’ll see on a dock.
2-way vs. 4-way entry
- A 2-way stringer pallet has solid stringers. Forklift and pallet jack forks enter only from the two ends.
- A 4-way (partial 4-way) stringer pallet has notches cut into the stringers. Forklift forks can enter from all four sides; pallet jacks still only enter from the two ends because the notches are above the floor. Most GMA pallets are this type.
Stringer pallets are cheaper to build, lighter, and easy to repair (a companion board alongside a cracked stringer restores it). Their weak point is the notch, which reduces the stringer’s cross section right where forks hit it.
Block pallets
A block pallet replaces the three stringers with nine solid blocks (four corners, four sides, one center) connected by stringer boards, with top and bottom decks nailed on. This is the design used by pooled pallet systems (the blue CHEP pallet is a block pallet) and by heavy-duty and export applications.
Block pallets are true 4-way entry: forklifts and pallet jacks both enter from any side because the openings go all the way to the floor. They’re stronger, more stable in racking, more uniform, and heavier. They’re also more expensive and harder to repair.
Side by side
| Stringer pallet | Block pallet | |
|---|---|---|
| Supports | 3 stringers (2×4) | 9 blocks + stringer boards |
| Forklift entry | 2-way, or 4-way if notched | 4-way |
| Pallet jack entry | 2-way only | 4-way |
| Weight (48×40) | ~35 to 50 lb | ~60 to 70 lb |
| Cost | Lower | Higher |
| Repair | Easy | Harder |
| Racking stability | Good | Better |
| Typical use | General freight, one-way shipping, most warehouses | Pooled systems, automation, heavy loads, export |
How much weight can a pallet hold?
There are three numbers, and mixing them up is how racks get overloaded.
- Static load. Pallet sitting flat on the floor. Highest number. A standard new hardwood GMA stringer pallet is typically rated around 4,600 lb.
- Dynamic load. Pallet being moved by forklift or jack, where the forks concentrate the load. Typically around 2,500 lb for the same pallet.
- Racked load. Pallet supported only at its edges on rack beams, with nothing under the middle. This is the lowest number and the one that matters in a warehouse. Around 2,800 lb is a common published figure for a GMA stringer pallet on 40 inch beam spacing, but it drops sharply if the pallet is racked on the wrong axis, is a Grade B with a repaired stringer, or has a thin bottom deck.
Block pallets generally rate higher in all three because the load path goes through nine supports instead of three, and the bottom deck is fuller.
Every one of these figures is a category norm. The actual rating depends on species, board thickness, nail pattern, moisture, and repair history. If a load is heavy, get the rating for the specific pallet you’re buying in writing.
Which one should you buy?
- General freight, cost matters, pallets won’t come back: stringer, 4-way notched.
- Heavy or concentrated loads: block, or a heavy-duty stringer with thicker deck boards and hardwood.
- Racking above ground level: either, but make sure it’s rack-rated and racked with the stringers or stringer boards across the beams.
- Automation or conveyors: block, or whatever the equipment manufacturer specifies. Uniformity matters more than strength.
- Product doesn’t fit 48×40: custom, in whichever design suits the load.
Frequently asked questions
A pallet built on three parallel 2×4 boards (stringers) with deck boards nailed across the top and bottom. The standard 48×40 GMA pallet is a stringer pallet.
A 2-way pallet accepts forks only from its two ends. A 4-way pallet accepts forks from all four sides, either through notched stringers (partial 4-way) or a block design (true 4-way).
A standard new GMA pallet is typically rated around 2,500 lb dynamic, 4,600 lb static, and 2,800 lb racked. Ratings vary by construction; confirm for the pallet you buy.
Stronger and more stable, yes. Better depends on the job. For most general freight a stringer pallet does the work at lower cost.
Need pallets rated for your load?
A&A Pallets builds stringer and block pallets in Dallas, new or recycled lumber, standard or custom size, and repairs both. Tell us the load and we’ll spec it. Call (214) 398-3555.
Related services: Custom Pallets · Pallet Repair · New & Recycled Pallets · All services
Photo: W.carter via Wikimedia Commons, CC0 (source)